SV-15P Alcohol Parquet Adhesive
SV-15P Alcohol Parquet Adhesive
SV-15P is a ready to use solvent-containing parquet adhesive based upon Polyvinyl-acetate and synthetic resins. Suitable for bonding many types of parquet floors onto suitable indoor substrates.
- Ready to use
- Low consumption/m²
- Free of water
- Very easy to apply
- Forms stable peaks once applied by a notched trowel or spreader comb
- Rapid build up of bond strength
- Rapid curing
- High final bond strength (according to DIN 281)
- Hard-elastic bond
- Low consumption/m²
- Free of water
- Very easy to apply
- Forms stable peaks once applied by a notched trowel or spreader comb
- Rapid build up of bond strength
- Rapid curing
- High final bond strength (according to DIN 281)
- Hard-elastic bond
SV-15P is suitable for indoor bonding of wooden floors with small dimensions (up to max. 250 x 50mm) such as solid, stab, pre-finished, and on-end parquet, wood-plank, wood-block and
laminates.
Not suitable for wooden floors and multi-layer or ready to use parquet with large dimensions.
Therefor use MS-30P Parquet Adhesive or PU-20P 2-component Parquet adhesive.
Suitable for use on porous substrates such as concrete, screeds, wood, mosaic, chipboard and OSB Board (large particle size chipboard). Do not
use on pretreated wood.
laminates.
Not suitable for wooden floors and multi-layer or ready to use parquet with large dimensions.
Therefor use MS-30P Parquet Adhesive or PU-20P 2-component Parquet adhesive.
Suitable for use on porous substrates such as concrete, screeds, wood, mosaic, chipboard and OSB Board (large particle size chipboard). Do not
use on pretreated wood.
SV-15P should be acclimatised to room temperature before installation.
Apply the adhesive to the surface by means of a suitable notched SOUDAL trowel N° 3. Do not apply more to the surface that can be covered with
parquet within 10 minutes. Slide the parquet onto the adhesive layer and tap into place or tamp down with a rubber hammer.
A minimum of 80% contact coverage is required to ensure a perfect adhesion. Loading the parquet with weights will improve the final bond strength. Wait at least 24 hours before sanding and finishing
the parquet. Uncured SV-15P may be removed from tools and
parquet with SOUDAL Adhesive cleaner. Cured adhesive must be removed mechanically.
Apply the adhesive to the surface by means of a suitable notched SOUDAL trowel N° 3. Do not apply more to the surface that can be covered with
parquet within 10 minutes. Slide the parquet onto the adhesive layer and tap into place or tamp down with a rubber hammer.
A minimum of 80% contact coverage is required to ensure a perfect adhesion. Loading the parquet with weights will improve the final bond strength. Wait at least 24 hours before sanding and finishing
the parquet. Uncured SV-15P may be removed from tools and
parquet with SOUDAL Adhesive cleaner. Cured adhesive must be removed mechanically.
- Never install to substrates, which are not protected against possible
rising damp.
- Do not apply the adhesive at temperatures below 15°C or above 25°C
- Minimum temperature of the substrate should be at least 15°C.
- Do not apply the adhesive when the relative humidity is above 75%.
- Never install onto a substrate which contains too much moisture or
onto substrates with a higher humidity value than recommended by
the wood supplier.
- Never install wood which is too dry (<7% humidity). This can expand
at higher humidity or when the humidity rises and cause damage.
- Do not install if the walls and ceilings of the area are not dry
(e.g. after plastering or painting etc.)
- Do not dilute the adhesive
rising damp.
- Do not apply the adhesive at temperatures below 15°C or above 25°C
- Minimum temperature of the substrate should be at least 15°C.
- Do not apply the adhesive when the relative humidity is above 75%.
- Never install onto a substrate which contains too much moisture or
onto substrates with a higher humidity value than recommended by
the wood supplier.
- Never install wood which is too dry (<7% humidity). This can expand
at higher humidity or when the humidity rises and cause damage.
- Do not install if the walls and ceilings of the area are not dry
(e.g. after plastering or painting etc.)
- Do not dilute the adhesive